Boost Your Productivity!Translate documents (Ms-Word, Ms-Excel, ...) faster and better thanks to artificial intelligence!
https://pro.wordscope.com
https://blog. wordscope .com
Broad-flanged cap
Connecting-rod eye
Cylinder top
Diameter at small end
Diameter small end
Full size
Full-feature
Fully-featured
High-end
Little end
Open top end with increased curl diameter
Small end
Small end diameter
Stand-height diameter
Steel end top sheet
Steel end-top
Top diameter
Top end
Top end diameter
Top end sheet
Top-end
Top-height diameter
Top-marked
Top-of-the-line
Top-of-the-range
Up market
Up-market
Upper end
Wide flange fold lid

Traduction de «top end diameter » (Anglais → Français) :

TERMINOLOGIE
voir aussi les traductions en contexte ci-dessous
top end diameter | diameter at small end

diamètre au petit bout


top diameter [ small end diameter | diameter small end ]

diamètre au fin bout [ diamètre fin bout | diamètre au petit bout ]


broad-flanged cap | open top end with increased curl diameter | wide flange fold lid

couvercle à collet large | couvercle avec large bord à sertir


steel end-top [ steel end top sheet | top end sheet ]

tôle supérieure de bout


up market | up-market | top-of-the-line | top-of-the-range | top-marked | top-end | full size | fully-featured | full-feature | high-end

haut de gamme


high-end [ top-of-the-line | top-of-the-range | top-end ]

haut de gamme [ de haute gamme ]


stand-height diameter | top-height diameter

diamètre moyen des prédominants


stand-height diameter | top-height diameter

diamètre moyen des prédominants


small end | little end | top end | upper end | connecting-rod eye

pied de bielle


TRADUCTIONS EN CONTEXTE
(7) On tenders of the Vanderbilt type, with three filling holes, there shall be a hand rail four inches above the level of the top running board not less than one inch in diameter, extending from the present hand rail, which extends from the coal space to within 20 inches of the first filling hole, to the rear end of the tender at each side of the top running board.

(7) Sur les tenders du type Vanderbilt ayant trois trous de remplissage, il doit y avoir, à quatre pouces au-dessus du niveau de la passerelle du dessus, une main courante d’au moins un pouce de diamètre. Cette main courante doit s’étendre de la main courante existante, qui va de la soute à charbon à moins de 20 pouces du premier trou de remplissage, jusqu’à l’extrémité arrière du tender, de chaque côté de la passerelle du dessus.


disc-shaped components of between 75 mm (3 in.) and 400 mm (16 in.) diameter especially designed or prepared to fit to the ends of the rotor tube, and so contain the UF within the rotor tube, and in some cases to support, retain or contain as an integrated part an element of the upper bearing (top cap) or to carry the rotating elements of the motor and lower bearing (bottom cap), and manufactured from high strength to density ratio ...[+++]

composants en forme de disque d’un diamètre compris entre 75 mm (3 po) et 400 mm (16 po) spécialement conçus ou préparés pour s’adapter aux extrémités du bol et maintenir ainsi l’UF à l’intérieur de celui-ci et, dans certains cas, pour porter, retenir ou contenir en tant que partie intégrante un élément du palier supérieur (bouchon supérieur) ou pour porter les éléments tournants du moteur et du palier inférieur (bouchon inférieur), et fabriqués dans des matériaux ayant un rapport résistance-densité élevé.


6. Top or bottom caps of between 75 mm and 400 mm diameter to fit the ends of a rotor tube, made from 'high strength-to-density ratio materials';

6. couvercles supérieurs ou inférieurs d'un diamètre compris entre 75 et 400 mm conçus pour s'adapter aux extrémités d'un tube de rotor et constitués de matériaux ayant un rapport résistance-densité élevé;


6. Top or bottom caps of between 75 mm and 400 mm diameter to fit the ends of a rotor tube, made from "high strength-to-density ratio materials";

6. couvercles supérieurs ou inférieurs d'un diamètre compris entre 75 et 400 mm conçus pour s'adapter aux extrémités d'un tube de rotor et constitués de matériaux ayant un rapport résistance-densité élevé;


For more results, go to https://pro.wordscope.com to translate your documents with Wordscope Pro!
(bb) maximum butt-end diameter, 14 mm except in the case of top-graft cuttings for grafting plants in situ.

bb) diamètre maximum au plus gros bout 14 mm, sauf s'il s'agit de boutures-greffons destinées au greffage sur place.




D'autres ont cherché : broad-flanged cap     connecting-rod eye     cylinder top     diameter at small end     diameter small end     full size     full-feature     fully-featured     high-end     little end     small end     small end diameter     stand-height diameter     steel end top sheet     steel end-top     top diameter     top end     top end diameter     top end sheet     top-end     top-height diameter     top-marked     top-of-the-line     top-of-the-range     up market     up-market     upper end     wide flange fold lid     


datacenter (1): www.wordscope.fr (v4.0.br)

'top end diameter' ->

Date index: 2022-07-09
w