Boost Your Productivity!Translate documents (Ms-Word, Ms-Excel, ...) faster and better thanks to artificial intelligence!
https://pro.wordscope.com
https://blog. wordscope .com
Bottom of watertight bulkhead
Bulkhead connection
Bulkhead fitting
Bulkhead luminaire
Bulkhead union
Partial bulkhead
Partial watertight bulkhead
Watertight bulkhead
Watertight bulkhead fitting
Watertight lighting fitting

Traduction de «watertight bulkhead fitting » (Anglais → Français) :

TERMINOLOGIE
voir aussi les traductions en contexte ci-dessous


partial bulkhead | partial watertight bulkhead

cloison partielle étanche


bulkhead union [ bulkhead connection | bulkhead fitting ]

raccord de traversée de cloison [ raccord de traversée ]












watertight lighting fitting

luminaire étanche à l'immersion
TRADUCTIONS EN CONTEXTE
(b) where a watertight bulkhead is pierced by pipes, scuppers, electric cables or other similar fittings, provision shall be made that will ensure that the watertightness of the bulkhead is not thereby impaired; and

b) si des tuyaux dalots, câbles électriques ou autres garnitures semblables traversent une cloison étanche, des dispositions seront prises pour empêcher que l’étanchéité de ces cloisons en soit diminuée; et


(3) Openings in watertight bulkheads shall be fitted with watertight doors of ample strength to withstand the water pressure to which they may be subjected and they shall be carefully fitted and constructed.

(3) Les ouvertures pratiquées dans les cloisons étanches seront munies de portes étanches soigneusement construites et ajustées et offrant une résistance amplement suffisante pour supporter la pression d’eau à laquelle elles seront soumises.


(2) In ships 131 m in length and upwards, the watertight bulkhead next abaft the collision bulkhead shall be fitted at a distance from the forward perpendicular that is not greater than the permissible length appropriate to a compartment bounded by the forward perpendicular and such bulkhead.

(2) Pour les navires d’une longueur de 131 m ou plus, la première cloison étanche en arrière de la cloison d’abordage sera placée à une distance de la perpendiculaire avant égale au plus à la longueur admissible pour un compartiment limité par la perpendiculaire avant et une telle cloison.


18 (1) Every door required by these Regulations to be watertight shall be of such design, material and construction as will maintain the integrity of the watertight bulkhead in which it is fitted; any such door giving direct access to any space that may contain bunker coal shall, together with its frame, be made of cast or mild steel; any such door in any other position shall, together with its frame, be made of cast or mild steel or cast iron.

18 (1) Toute porte qui, aux termes du présent règlement, doit être étanche devra de par son tracé, les matériaux utilisés et la construction, conserver son intégrité à la cloison étanche dans laquelle elle est installée. Toute porte de ce genre donnant directement accès à tout espace qui pourrait contenir du charbon de soute devra, de même que son cadre, être faite en fonte d’acier ou en acier doux.


For more results, go to https://pro.wordscope.com to translate your documents with Wordscope Pro!
24 (1) Subject to subsection (2), a fishing vessel shall be fitted with two main transverse watertight bulkheads, one located forward of amidships at a distance not exceeding 35 per cent of the length of the vessel and the other located aft of amidships at a distance not exceeding 45 per cent of the length of the vessel, and the construction of the bulkheads shall be in accordance with Schedule III.

24 (1) Sous réserve du paragraphe (2), un bateau de pêche doit avoir au moins deux cloisons transversales principales qui sont étanches et construites conformément à l’annexe III, dont l’une est située à l’avant du bateau à une distance du milieu n’excédant pas 35 pour cent de la longueur du bateau et l’autre, à l’arrière du bateau, à une distance du milieu n’excédant pas 45 pour cent de la longueur du bateau.


If side structural sponsons are fitted to enable compliance with this regulation, and as a consequence there is an increase in the breadth (B) of the ship and hence the vessel's B/5 distance from the ship's side, such modification shall not cause the relocation of any existing structural parts or any existing penetrations of the main transverse watertight bulkheads below the bulkhead deck (see fig 5)

Si des caissons latéraux de stabilité sont installés afin de respecter la présente règle, ce qui a pour effet d'augmenter la largeur (B) du navire et, par conséquent, la distance B/5 par rapport aux côtés du navire, cette modification ne doit pas entraîner le déplacement de parties structurelles existantes ni des passages des principales cloisons transversales étanches à l'eau au-dessous du pont de cloisonnement (cf. fig. 5).


1. Transverse or longitudinal bulkheads/barriers which are fitted and taken into account to confine the movement of assumed accumulated water on the damaged ro-ro deck need not be strictly "watertight".

1. Les cloisons/barrières transversales ou longitudinales existantes et dont il est tenu compte pour contenir le mouvement de l'eau supposée s'être accumulée sur le pont roulier endommagé ne doivent pas être complètement étanches à l'eau.




datacenter (1): www.wordscope.fr (v4.0.br)

'watertight bulkhead fitting' ->

Date index: 2021-12-04
w